Needlework System 4 - Light & Accessory Holder
The Light & Accessory Holder by Needlework System 4. The most versatile stitching stand on the market!
- Holder provides a secure method to attach most clamp/post lights to your stand
- For use with the Standard and Travel-Mate floor stands only - not compatible with Lap Stand or Table Clamp
- Holder has T-shaped extension that can hold 2 separate accessories
- Holder is needed to use the Scissor Tray with your floor stand
- This attachment is needed to position a clamp light or magnifier over your canvas
- Any clamp light or magnifier (opening at least 1-inch) will work on the Holder
- Stella EDGE Clamp light can clamp to one side of this Holder (sold separately)
- To attach - remove the two silver wingnuts from silver C-shaped bar. Wrap C-shaped bar around main shaft of your floor stand (ex. sideways to position holder on the back). Attach holder back onto C-shaped bar. Adjust height as needed (up or down), then tighten wingnuts. Can be positioned on any side of the floor stand
- Total dimensions: 5.5" x 3". and weighs less than 9 oz.
- T-Bar section dimensions: is 3" long, 1" wide, 1" deep (this is where you attach a light, the Scissor Tray, or a magnifier)
- T-Bar section can be adjusted/leveled up or down with the included Tri-Knob
- Holder has 2 cylinders cut into it, each with a tightening screw. One can be used for the Scissor Tray. One cylinder can be used to hold most peg-base swivel-arm lights
- This accessory is also called the Light & Magnifier Holder (or Light & Tray Holder)
- Proudly made in the USA
- Made of extruded aluminum, which is strong and lightweight
- Each System 4 component is sold separately, so you can order exactly what you need
- System 4 products are in stock and ship directly from our Raleigh, NC retail location
- Needlework System4 products have a limited lifetime warranty, covering factory defects on all stands and metal accessories they manufacture
Shown being used on the Floor Stand, with Scissor Tray attached, holding the Stella EDGE Clamp Light, and configured with the Frame Clamp (each sold separately).
USER TIP - Aways fully separate the mating teeth when adjusting /changing accessories, or damage will occur and the teeth will not hold. Loosen the knob enough that the teeth fully separate, and be sure teeth match before tightening.
USER TIP - Always remove attachments when traveling with your stand.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Needlework System 4 - Light & Accessory Holder
Needlework System 4 - Light & Accessory Holder
The Light & Accessory Holder by Needlework System 4. The most versatile stitching stand on the market!
- Holder provides a secure method to attach most clamp/post lights to your stand
- For use with the Standard and Travel-Mate floor stands only - not compatible with Lap Stand or Table Clamp
- Holder has T-shaped extension that can hold 2 separate accessories
- Holder is needed to use the Scissor Tray with your floor stand
- This attachment is needed to position a clamp light or magnifier over your canvas
- Any clamp light or magnifier (opening at least 1-inch) will work on the Holder
- Stella EDGE Clamp light can clamp to one side of this Holder (sold separately)
- To attach - remove the two silver wingnuts from silver C-shaped bar. Wrap C-shaped bar around main shaft of your floor stand (ex. sideways to position holder on the back). Attach holder back onto C-shaped bar. Adjust height as needed (up or down), then tighten wingnuts. Can be positioned on any side of the floor stand
- Total dimensions: 5.5" x 3". and weighs less than 9 oz.
- T-Bar section dimensions: is 3" long, 1" wide, 1" deep (this is where you attach a light, the Scissor Tray, or a magnifier)
- T-Bar section can be adjusted/leveled up or down with the included Tri-Knob
- Holder has 2 cylinders cut into it, each with a tightening screw. One can be used for the Scissor Tray. One cylinder can be used to hold most peg-base swivel-arm lights
- This accessory is also called the Light & Magnifier Holder (or Light & Tray Holder)
- Proudly made in the USA
- Made of extruded aluminum, which is strong and lightweight
- Each System 4 component is sold separately, so you can order exactly what you need
- System 4 products are in stock and ship directly from our Raleigh, NC retail location
- Needlework System4 products have a limited lifetime warranty, covering factory defects on all stands and metal accessories they manufacture
Shown being used on the Floor Stand, with Scissor Tray attached, holding the Stella EDGE Clamp Light, and configured with the Frame Clamp (each sold separately).
USER TIP - Aways fully separate the mating teeth when adjusting /changing accessories, or damage will occur and the teeth will not hold. Loosen the knob enough that the teeth fully separate, and be sure teeth match before tightening.
USER TIP - Always remove attachments when traveling with your stand.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
The Light & Accessory Holder by Needlework System 4. The most versatile stitching stand on the market!
- Holder provides a secure method to attach most clamp/post lights to your stand
- For use with the Standard and Travel-Mate floor stands only - not compatible with Lap Stand or Table Clamp
- Holder has T-shaped extension that can hold 2 separate accessories
- Holder is needed to use the Scissor Tray with your floor stand
- This attachment is needed to position a clamp light or magnifier over your canvas
- Any clamp light or magnifier (opening at least 1-inch) will work on the Holder
- Stella EDGE Clamp light can clamp to one side of this Holder (sold separately)
- To attach - remove the two silver wingnuts from silver C-shaped bar. Wrap C-shaped bar around main shaft of your floor stand (ex. sideways to position holder on the back). Attach holder back onto C-shaped bar. Adjust height as needed (up or down), then tighten wingnuts. Can be positioned on any side of the floor stand
- Total dimensions: 5.5" x 3". and weighs less than 9 oz.
- T-Bar section dimensions: is 3" long, 1" wide, 1" deep (this is where you attach a light, the Scissor Tray, or a magnifier)
- T-Bar section can be adjusted/leveled up or down with the included Tri-Knob
- Holder has 2 cylinders cut into it, each with a tightening screw. One can be used for the Scissor Tray. One cylinder can be used to hold most peg-base swivel-arm lights
- This accessory is also called the Light & Magnifier Holder (or Light & Tray Holder)
- Proudly made in the USA
- Made of extruded aluminum, which is strong and lightweight
- Each System 4 component is sold separately, so you can order exactly what you need
- System 4 products are in stock and ship directly from our Raleigh, NC retail location
- Needlework System4 products have a limited lifetime warranty, covering factory defects on all stands and metal accessories they manufacture
Shown being used on the Floor Stand, with Scissor Tray attached, holding the Stella EDGE Clamp Light, and configured with the Frame Clamp (each sold separately).
USER TIP - Aways fully separate the mating teeth when adjusting /changing accessories, or damage will occur and the teeth will not hold. Loosen the knob enough that the teeth fully separate, and be sure teeth match before tightening.
USER TIP - Always remove attachments when traveling with your stand.
